Основні

Виробник

SpeedyBee

Доставка в течение 2–3 недель.

SPEEDYBEE

ADAPTER 3

NO LAPTOP, NO POWER BANK, AND NO LIPO
CHECKER IN YOUR FPV BAG.

Turn your smartphone into
your mobile FPV companion

Connect to the SpeedyBee mobile app, and configure
your flight controller anytime, anywhere. Or flash the
latest version of Betaflight/Emuflight/INAV in just
2 minutes before your flight session.
The choice is yours.

Analyzing Blackbox data has
never been easier

No laptop, no separate app, no hassle. Connect your
quad to the SpeedyBee mobile app and analyze your
Blackbox data* in just 1.5 minutes after a flight.
Get the most out of your practice sessions now.

*Currently supports Betaflight and Emuflight only

Your LiPo batteries =
Powerful 30W power banks

Connect SpeedyBee Adapter 3 to a LiPo battery and
charge your mobile phone* and tablets when you
need them the most. Supports mainstream
QC3.0/AFC/Apple 2.4A (iPhone 6s and above)
and other fast charging protocols with charging
power up to 30W. Complete with over-current
protection, short-circuit protection and
over-temperature protection to protect
your gadgets from unwanted accidents.

Phone Model	Battery Capacity	Battery level after half an hour of charging
Mi 11 Ultra	5000mAh	52%
Samsung S10	3400mAh	49%
HUAWEI P40 Pro	4400mAh	45%
iPhone 11	3110mAh	22%

*Charging function requires 2S LiPo and above.

Forgot your LiPo checker?
Worry not

Connect your 1S - 6S LiPo and the display will
immediately show your battery voltage and the
remaining power with a specific colour code*.
The built-in beeper will alert you if the remaining
power is less than 40% to help extend your
battery lifespan.

*GREEN(>80%), WHITE(40-80%) and RED(<40%).

MicroUSB or Type C?
Why not both?

SpeedyBee Adapter 3 comes with a dual-head data cable,
with MicroUSB 2.0 and USB 3.0 Type C connector
on each end. No more worries about connector
compatibility regardless of what flight controller
you are using in your build.

WiFi + Bluetooth =
the best of both worlds

Use Bluetooth for quick access to
your firmware configurator,
or switch to Wi-Fi to flash
firmware or download
Blackbox data at a
higher speed.

And all you need
is just one LiPo

Access the configurator function using any LiPo
batteries available to you. Supports all 1S - 6S LiPo
with PH2.0 or XT60 connectors. Plug in that
beefy 6S 1500mah, or that tiny 1S Whoop battery
(minimum voltage 3.8V), to the
SpeedyBee Adapter 3
you are ready to
access the
configurator.

Specifications

Product Name	SpeedyBee Adapter 3
Power Input Voltage Range	1-6S(3.8V+ for 1S)
Power Input Connector	XT60-Male, PH2.0 male
Required Mobile Device System Version	Android 7.0+ \| iOS 12.0+
Supported SpeedyBee App Version	V1.6.1 + for iOS \| V1.5.6+ for Android
Supports Firmware	Configurators and Flashing: • Betaflight 3.2.0 and above • iNAV 2.0.0 and above • EmuFlight 0.1.0 and above Flashing only, excludes Configurators: • Ardupilot
Wireless signal transmission frequency	• Bluetooth frequency: 2402 - 2480 MHz • WiFi frequency: 2412 - 2484 MHz
Maximum Output Current for flight controllers	700mA @5V
Fast Charging Output interface	USB A Port
Minimum Input Voltage for Charging output	7.4V(2S LiPo)
Supported Fast Charging Protocol	• QC3.0/QC2.0 • AFC • FCP • SCP/High SCP • PE2.0/PE1.1 • SFCP
Max Fast Charging Current	3.5A
Max Fast Charging Power	30W
Case Material	ABS + PC
Liquid Silicone Cable Length	12.4cm
Dimension(Main Body)	24.821.853.6mm
Net Weight	35g

Package

1 x Adapter 3
1 x Manual Card

SpeedyBee Adapter 3 VS SpeedyBee Adapter 2 VS OTG

Item	SpeedyBee Adapter 3	SpeedyBee Adapter 2	OTG
Support 1-6S LiPo input	✔	✔	N/A
XT60 and PH2.0 connectors	✔	✔	N/A
BF/INAV/EMU configuration	✔	✔	✔
Flight control firmware upgrade	✔	✔	✘
Built-in WiFi	✔	✔	✘
Built-in Bluetooth	✔	✘	✘
Blackbox downloader and analyzer	✔	✘	✘
Built-in MicroUSB and Type C connector	✔	✘	✘
Fast charging output up to 30W	✔	✘	✘
Built-In LiPo Voltage Checker	✔	✘	✘